Structural Fire Damage Cleaning in Oxnard, CA
With the wallboard torn out, what is left is a skeleton of black studs, scorched rafters and smoke-stained block. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Oxnard who clean the framing, masonry and steel itself.
- Soda blasting, dry ice blasting and wire brushing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
The contractors we connect you with are independent businesses carrying their own license and insurance. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. How fast someone arrives depends on availability and distance, often within the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Let the crew confirm the structure will hold before anyone goes up, and keep everyone off the floor above a burned basement or crawlspace.
Structural Cleaning Services From Rafters to Slab
Furniture and debris are a separate job. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. Hand work is slower but sensible where a blast rig would be too much.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Ask your contractor which method they recommend for each area and why. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Containment matters here, since blast media and loosened soot travel anywhere the air moves. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask what the plan is to shield the undamaged rooms, floors and glass.
Bare Framing Covered in Soot and Char?
Phone our dispatchers and they begin searching for a structural crew close to Oxnard. It costs nothing to call.
Call +1-833-336-1630The Path From Charred Framing to Sealed Wood
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
What Callers Said About Their Structural Crew
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
Our basement fire blackened the block walls and the steel beam over the family room. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. The basement smells normal again, even closed up.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
The test is simple: they probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
If smoke reached the attic, almost always yes. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. It is vacuumed out with an insulation vac so the rafters and roof deck can be probed, blasted and sealed before anything new is blown in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Spalling or cracked masonry is a structural question for a mason or engineer.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. An engineer's report on trusses, headers, beams, steel and badly charred joists protects you and supports the claim. Your local building department may also require one before the walls close.
Structural Fire Cleaning Throughout Oxnard
Our dispatch line covers Oxnard and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
If the first crew we connect you with is not the right fit, call back and a dispatcher will connect you with another. Get the bones cleaned before anyone hangs new drywall.
